wiring diagram RENAULT KANGOO 2013 X61 / 2.G Passenger Comparment Connection Unit Workshop Manual

87B-2V1 MR-376-X76-87B000$010.mif
87B
UCH
VDiag No.: 0F
1. SCOPE OF THIS DOCUMENT
This document presents the fault finding method applicable to all computers with the following specifications:
2. PREREQUISITES FOR FAULT FINDING
Documentation type
Fault finding procedures (this document):
– Assisted fault finding (integrated into the diagnostic tool), Dialogys.
Wiring Diagrams:
– Visu-Schéma.
Type of diagnostic tools
–CLIP
Special tooling required
If the information obtained by the diagnostic tool requires the electrical continuity to be checked, connect
bornier Elé. 1622 or universal bornier Elé. 1681.
3. SAFETY INSTRUCTIONS
The safety instructions must be followed at all times when working on components in order to avoid damage or
injury:
– check the battery voltage to avoid incorrect operation of computer functions,
– use the proper tools.
*VLL — Very Long LifeVehicle(s): KANGOO VLL*Computer name: UCH
Function concerned: PASSENGER
COMPARTMENT CONNECTION UNITVdiag No.: 0F
Special tooling required:
Diagnostic tool
Multimeter
Elé. 1622Bornier
Elé. 1681Universal bornier
WARNING:
– All checks performed using bornier Elé. 1622 or Elé. 1681 must be performed with the battery disconnected.
– The bornier is only designed to be used with a multimeter. Never power the test points with 12 V.
UCH_V0F_PRELI
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding – Introduction

87B-11
AFTER REPAIRFollow the instructions.
Deal with any other faults.
Clear the stored faults.
V1 MR-376-X76-87B000$070.mif
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding – Interpretation of faults87B
UCH
VDiag No.: 0F
DF273
PRESENT
OR
STOREDIMPACT CONNECTION
NOTESSpecial notes:
The fault is present 8 seconds after the ignition is switched on and becomes stored
after the ignition is switched off.
Note:
If this fault is present, the door locking function while driving is inhibited.
Special note:
Use Wiring Diagrams Technical Note for Kangoo VLL.
Perform fault finding on the airbag function (see 88C, Airbags and pretensioners).
Check the connection and condition of the UCH connectors, component code 645.
If the connector or connectors are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the insulation, continuity and absence of interference resistance on the following connection:
●60BR between components 645 and 756.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the Techline
UCH_V0F_DF273

87B-19
AFTER REPAIRFollow the instructions.
Deal with any other faults.
Clear the stored faults.
V1 MR-376-X76-87B000$100.mif
87B
UCH
VDiag No.: 0F
ET004+ 12 VOLTS AFTER IGNITION
NOTESSpecial note:
Use Wiring Diagrams Technical Note for Kangoo VLL.
ET004: "NO" with the ignition on
Check fuse F15 (20 A) in the passenger compartment fuse and relay box, component code 260 (see MR 374,
Mechanical, 81C, Fuses, Fuses: List and location of components).
Using a multimeter, check for + 12 V after ignition on connection AP7 of the UCH connector, component code 645.
Using a multimeter, check for + 12 V on connection BP10 of the UCH connector, component code 645.
If the connection or connections are faulty and if there is a repair procedure (see Technical Note 6015A (Renault)
or Technical Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the wiring,
otherwise replace it.
If there is no voltage, check the continuity and the insulation to earth on the following connection:
●AP7 between components 645 and 260.
If the connection is faulty and if there is a repair procedure (see Technical Note 6015A (Renault) or Technical
Note 9804A (Dacia), Electrical wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise
replace it.
ET004: "YES" with the ignition off
Using a multimeter, check that there is no +12 V with the ignition off on connection AP7 of the UCH connector,
component code 645.
If the fault is still present, contact the techline.
UCH_V0F_ET004
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding – Interpretation of statuses

87B-20
AFTER REPAIRFollow the instructions.
Deal with any other faults.
Clear the stored faults.
V1 MR-376-X76-87B000$100.mif
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding – Interpretation of statuses87B
UCH
VDiag No.: 0F
ET127IMMOBILISER WARNING LIGHT
NOTESThe immobiliser warning light status should be OFF after the + after ignition feed is
switched on.
The immobiliser warning light status should be ON when the key is not in the ignition
switch.
Special note:
Use Wiring Diagrams Technical Note for Kangoo VLL.
Check the connection and condition of the instrument panel connector, component code 247.
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the connection and condition of the UCH connector, component code 645.
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Using a multimeter, check the continuity and insulation of the following connection:
●87H between components 645 and 247.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the techline.
UCH_V0F_ET127

87B-21
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any other faults.
Clear the stored faults.
V1 MR-376-X76-87B000$100.mif
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding – Interpretation of statuses87B
UCH
VDiag No.: 0F
ET489FRONT DOORS
NOTESCheck that no fault is present.
Open the front doors one after another.
Special note:
Use Wiring Diagrams Technical Note for Kangoo VLL.
Check that, for each front door open, status ET489 is OPEN or for each front door closed, the status is CLOSED.
Check the connection and wiring of the driver's door rabbet switch, component code 180 and the passenger's door
rabbet switch, component code 181.
If the connector or connectors are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the continuity and insulation of the following connections:
●13A between components 180 and 645,
●13N or 13A between components 181 and 645,
●MK between component 180 and earth,
●MF between component 181 and earth.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the continuity between the two connections of the door rabbet switches.
Pull the handle to open the lock and check that there is no longer any continuity between the two connections.
Check that the lock engages into the striker plate properly.
If the fault is still present, contact the techline.
UCH_V0F_ET489

87B-23
AFTER REPAIRCarry out another fault finding check on the system.
Deal with any other faults.
Clear the stored faults.
V1 MR-376-X76-87B000$100.mif
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding – Interpretation of statuses87B
UCH
VDiag No.: 0F
ET551REAR DOORS OR LUGGAGE COMPARTMENT
NOTESCheck that no fault is present.
Open the rear doors one after another, then open the luggage compartment.
Special note:
Use Wiring Diagrams Technical Note for Kangoo VLL.
Check that when one of the rear doors or the tailgate is opened, status ET551 is OPEN and that when the rear
doors or tailgate are closed, status ET551 is CLOSED.
Check the connection and wiring of the rabbet switch on the rear right-hand door, component code 178, the rabbet
switch on the rear left-hand door, component code 179 and of the tailgate opening switch, component code 560.
If the connector or connectors are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the continuity and insulation of the following connections:
●13N or 13A between components 179 and 645,
●13N or 13A between components 178 and 645,
●MG between component 179 and the earth,
●MF between component 178 and earth,
●MG between component 560 and earth,
●13N or 13A between components 560 and 645.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the continuity between the two connections of the rabbet switches for the doors and the tailgate.
Pull the handle to open the lock and check that there is no longer any continuity between the two connections.
Check that the lock engages into the striker plate properly.
If the fault is still present, contact the techline.
UCH_V0F_ET551

87B-26
AFTER REPAIRCarry out a road test, followed by a check with the diagnostic tool.
V1 MR-376-X76-87B000$130.mif
87B
UCH
VDiag No.: 0F
AC003IMMOBILISER WARNING LIGHT
NOTESThere must be no present or stored faults.
Activate the command and note whether the warning light illuminates (3 seconds).
Special note:
Use Wiring Diagrams Technical Note for Kangoo VLL.
Check the connection and condition of the instrument panel connector, component code 247.
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Check the connection and condition of the UCH connector, component code 645.
If the connector is faulty and there is a repair method (see Technical Note 6015A, Repairing electrical wiring,
Wiring: Precautions for repair), repair the connector, otherwise replace the wiring.
Using a multimeter, check the continuity and insulation of the following connection:
●87H between components 645 and 247.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, contact the techline.
UCH_V0F_AC003
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding – Interpretation of commands

87B-32
AFTER REPAIRCheck the system operation.
V1 MR-376-X76-87B000$150.mif
87B
UCH
VDiag No.: 0F
ALP1 No dialogue with the computer
NOTESSpecial note:
Use Wiring Diagrams Technical Note for Kangoo VLL.
Test the diagnostic tool on another vehicle which is in perfect working order.
Check:
– the connection between the diagnostic tool and the diagnostic socket, component code 225 (cable in good
condition),
– the engine and passenger compartment fuses (see MR 374, Mechanical, 81C, Fuses, Fuses: List and
location of components).
Check for + 12 V before ignition on the following connection:
●BP10 of component 225.
Check for + 12 V after ignition on the following connection:
●AP10 of component 225.
Check for an earth on the following connections:
●MK and NA of component 225.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the continuity of the following connection:
●HK between components 225 and 120.
If the connection is faulty and there is a repair procedure (see Technical Note 6015A, Electrical wiring repair,
Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Connect the bornier and check the insulation, continuity and absence of interference resistance on the
following connections:
●BP10 between components 645 and 260,
●AP7 between components 645 and 260,
●NA between component 645 and earth,
●HK between components 645 and 225.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
UCH_V0F_ALP01
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding – Fault Finding Chart

87B-33
AFTER REPAIRCheck the system operation.
V1 MR-376-X76-87B000$150.mif
PASSENGER COMPARTMENT CONNECTION UNIT
Fault finding – Fault Finding Chart87B
UCH
VDiag No.: 0F
ALP6 Heated rear screen not working
NOTESOnly consult this customer complaint after a complete check with the diagnostic
tool.
Special note:
Use Wiring Diagrams Technical Note for Kangoo VLL.
Check for the presence and condition of fuses F31 (10 A) and F14 (15 A) of the heated rear screen switch,
component code 128 and fuse F7 (30 A) of the heated rear screen relay, component code 235 on the passenger
compartment fuse and relay box, component code 260 (see MR 374, Mechanical, 81C, Fuses, Fuses: List and
location of components).
Check the continuity and insulation of the following connections:
●AP3 between components 128 and 260,
●LPG between components 128 and 260,
●BP15 between components 235 and 260.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
Check the continuity and insulation of the following connections:
●15A between components 200 and 128,
●15LP between components 128 and 235,
●MG between earth and component200.
●MK between earth and components 128 and 235.
If the connection or connections are faulty and there is a repair procedure (see Technical Note 6015A, Electrical
wiring repair, Wiring: Precautions for repair), repair the wiring, otherwise replace it.
If the fault is still present, refer to MR 374, Mechanical, 84A, Controls – Signals, Heated rear screen: Repair,
otherwise contact the Techline.
UCH_V0F_ALP06